T&R Test Equipment : 200ADM-P Specification

test equipment manufacturers, high voltage test equipment, high voltage equipment, ac flash testers, dc cable test sets, cable test equipment, cable testing systems, micro ohmmeters, ductor, low resistance measurement, relay test equipment, protective relay test, high current test equipment, primary injection, secondary injection, three phase test, g59 testing, rocof relay testing, dvs3, dsm200, dsm600, 100adm, 20adm, 500adm, cs100Trusted by customers world-wide, T&R Test Equipment Ltd. is the UK's leading manufacturer of heavy current and high voltage electrical test equipment. Quality and reliability are ductor, low resistance measurement of relay test equipment, protective relay test paramount importance to us, and our ISO9001:1994 high current test equipment, primary injection approval reflects this. Our broad product range includes relay test equipment, primary current high voltage equipment, ac flash testers injection systems, test equipment manufacturers, high voltage test equipment micro-ohmmeters, DC cable test sets and AC flash testers. The unit has a range of outputs allowing injection of currents between a few mA and and 100A. Voltages- up to 240V are available on high voltage equipment, ac flash testers the main outputs, allowing high impedance current relays dc cable test sets, cable test equipment and voltage relays to be tested. Three true RMS metering ranges are provided, allowing the full scale of the meter and trip level to be set independently of the selected test equipment manufacturers, high voltage test equipment output. Industry cable testing systems, micro ohmmeters standard connectors are used on all inputs and outputs for convenience, reliability and safety. A three phase test, g59 testing range of optional dsm200, dsm600 auxiliary supply modules are available to complement the dc cable test sets, cable test equipment unit. These fit neatly into the case alongside the main high current test equipment, primary injection unit. Options cable testing systems, micro ohmmeters are available for fixed or variable relay test equipment, protective relay test auxiliary ac or dc supplies. Please ductor, low resistance measurement see the specification overleaf for details.For example, testing a CDG11 disc induction dc cable test sets, cable test equipment over-current relay without a filter causes significant timing errors. The results below show the errors for a 1.3s 1A CDG11 over-current relay on its 0.5A test equipment manufacturers, high voltage test equipment plug setting, rocof relay testing, dvs3 tested at 5A. Three filter units are available: high voltage equipment, ac flash testers the 100ADM-F, the 100AFS, and the 100AFS-PH. All three ductor, low resistance measurement units have the same filtering characteristics and have current ranges covering 0.25A to 100A. The 100ADM-F is supplied three phase test, g59 testing in an relay test equipment, protective relay test insulated case to cable testing systems, micro ohmmeters match the 100ADM, complete with protective cover and carrying strap. The 100AFS has a steel case dsm200, dsm600 with carrying handles, but is otherwise high current test equipment, primary injection functionally test equipment manufacturers, high voltage test equipment similar and electrically identical to the 100ADM-F. The 100AFS-PH has all the features of the 100AFS, and also has a four position phase high voltage equipment, ac flash testers selector switch to simplify testing of three phase relays.The CIT has a flexible timing system , allowing timing tests to be carried out to a resolution of 1ms. Selection for normally open or normally closed contacts is automatic, and the status of the dc cable test sets, cable test equipment contacts is test equipment manufacturers, high voltage test equipment shown on the front panel. Timing modes are available to test under dc cable test sets, cable test equipment and over current devices, re-closers, under and high current test equipment, primary injection over voltage ductor, low resistance measurement devices, and many current trips and circuit breakers. The CI differs from the CIT in that it does not have a timing system. The CI & CIT primary current injection systems three phase test, g59 testing are ideally suited to commissioning and maintenance high current test equipment, primary injection testing rocof relay testing, dvs3 where high currents up to 3000A are required. The ductor, low resistance measurement systems consists dsm200, dsm600 of separate control and loading relay test equipment, protective relay test units for maximum flexibility. The high voltage equipment, ac flash testers control unit cable testing systems, micro ohmmeters contains relay test equipment, protective relay test all control and metering circuitry, and is linked to the loading unit by control and metering cables. The units are capable of injection of currents up to 3000A with an LU3000LP loading test equipment manufacturers, high voltage test equipment unit.

» Products » Current Injection

Main Output

The main output on the unit has four taps, allowing the selection of output voltages up to 240V and output currents up to 200A.

	Current				Output @230V
Range	Continuous	5 min*	1 min*	6 sec**	O/CV	Load V
10V	33A	67A	100A	200A	10.6V	8.7V@100A
35V	10A	20A	30A	-	36V	32V@30A
100V	3A	6A	10A	-	108V	99V@10A
240V	1A	2A	3A	-	276V	259V@3A
240Vdc	1A	2A	3A	-

*Off time of 15 minutes. On times based on an ambient temperature of 25°C.
**6 second intermittent ratings available with 230V supply.

Protection: over current trip, duty cycle trip, thermal monitoring.

I Limit Mode

The main output has a current limit mode that gives very fine control of output currents up to 10A. It also allows fine current control into very low impedance loads such as digital relays.

	Current				Output @230V
Range	Short Circuit	Continuous	5min	2min	O/CV	Load V
10V	10A	3A	6A	10A	8.6V	5V@6A
35V	3A	1A	2A	3A	29V	132V@30A
100V	1A	0.3A	0.6A	1A	88V	99V@10A
240V	0.3A	0.1A	0.2A	0.3A	224V	259V@3A

Auxiliary DC Output

Range	Maximum A	Continuous Rating
12-60V	1A	25W
60-220V	0.23A	25W

Protection: current limit

Phase-shifting AC Output

	Maximum Output Voltage		Current	Current
Range	No Load	Full load	Continuous	5 min on/15 min off
0-130V	144V	125V	0.23A	0.46A
0-260V	288V	250V	0.11A	0.23A
0-6V	6.6V	5V	5A	10A

Frequency range: 45—100Hz
Phase angle: 0—±180°
Protection: current limit & electronic trip.

Metering

The output is metered by a digital true RMS system with a single cycle capture memory ammeter—whenever the timer stops and the output is switched off, the current reading is held on the display. The RMS value of a single cycle can be captured. A current trip is set to 110% of full scale of the selected metering range.

Range	Resolution	Trip current	Accuracy	Aquisition time
5.000A	0.001A	5.5A	±0.5% rdg±5d	20ms
20.00A	0.01A	22A	±0.5% rdg±5d	20ms
50.00A	0.01A	55A	±0.5% rdg±5d	20ms
200.0A	200.0A	220A	±0.5% rdg±5d	20ms

Auxiliary Metering Inputs

Setting	Range	Resolution	Accuracy
Vdc/ac rms	300.0V	0.1V	±0.7% rdg±5d
Idc/ac rms	5.000A CF<3 9.999A CF<1.5	0.001A	±0.7% rdg±5d
Phase	-179.9° to +180.0°	0.1°	±3°
Frequency	40-100Hz	0.01Hz	±0.02% rdg±2d

Protection: fuse on current input

Timing System

Range	0-999.999s/9999.99s/99999.9s autoranging
Resolution	1/10/100ms
Accuracy	0.01%rdg+2d (+4d current operated mode)
Contact o/c	24V
Contact s/c	20mA
Vdc	24—240V

Each contact circuit will auto-select for normally open or normally closed contacts. A DC voltage of 24—240Vdc may also be used to trigger either timer channel. Contact state is shown by an LED.

Supply Requirements

115V/230V ±10% auto-selecting 50/60Hz 1ph 2300VA max.

Safety

An earth terminal is provided for connection to a local earth. The unit is designed to comply with BSEN61010 and is CE marked.

Temperature Range

Storage -20°C to 60°C
Operating0°C to 45°C

Standard Accessories

The 200ADM-P is supplied with operating manual, mains lead and,output lead set and spare fuses.

Optional Accessories

USB keyboard, 2Gb USB memory key, 100ADM-F filter unit, RB10 resistor box, printer kit.

The unit is supplied as standard in an aluminium case with removable lid. The unit is also available in a plastic Pelicase as an option. Please note that the Pelicase lid is not removable andopens as far as shown in the picture below.

Weights and Dimensions

	Dimensions	Weight
Standard unit	380mm x 314mm x 221mm	19.5kg
Pelicase unit	560mm x 456mm x 265mm	23.3kg

200ADM-P in standard aluminium case

Pelicase option

Other Pages

	Current Injection
	200ADM Current Injection System
	100ADM mk4 Current Injection System
	100ADM-F Current Filter Unit
	100A/E Current Injection system
	CIT Primary Current Injection System
	PCU1 Primary Current Injection System
	PCU2 Primary Current Injection System
	50A-3PH Three Phase Current Injection System
	200A-3PH/ED Three Phase Current Injection System
	750ADM mk2 Current Injection System
	750ADM-AL Lead Set
	200ADM-P Current Injection System
	200ADM-P Specification
	100/200ADM-AL Lead set
	RB10 Resistor Box

Sub Categories


	T&R Test Equipment \| Tel. +44 (0)1483 207428 info@trtest.com \| Top \| Site map

Company Overview

Contact

Staff Profile

T&R Group

Feedback

Employment

Complete Catalogue

Data Sheets

Application Notes

Obsolete Products

Support Home

FAQs

Support Request

Repairs and Calibration

Testing services

UK Distributors

Worldwide

Become an Agent

Distributor Area

Current Injection

Relay Test

High Voltage AC

High Voltage DC Cable Test Systems

Micro-Ohmmeters

Customer Specified Products

T&R Test Equipment : Welcome - test equipment manufacturersT & R Test Equipment Ltd manufacture a broad range of test equipment for the global electrical supply industry. the range includes relay test systems, current injection systems up to 6000A and high voltage systems up to 100kV.test equipment manufacturers, high voltage test equipment, high voltage equipment, ac flash testers, dc cable test sets, cable test equipment, cable testing systems, micro ohmmeters, ductor, low resistance measurement, relay test equipment, protective relay test, high current test equipment, primary injection, secondary injection, three phase test, g59 testing, rocof relay testing, dvs3, dsm200, dsm600, 100adm, 20adm, 500adm, cs100